STEP 7 SIEMENS USB TO MPI SERIAL
STEP 7 SIEMENS USB TO MPI DRIVERS
STEP 7 SIEMENS USB TO MPI DRIVER
STEP 7 SIEMENS USB TO MPI SOFTWARE

STEP 7 SIEMENS USB TO MPI DRIVER

The adapter does not support 'PC Adapter (PROFIBUS)' option.Дў, Click on 'Local Connection' option to set the parameters of COM port, correct choose the COM port in the equipment manager after the driver of USB / MPI + USB has been installed, select the 19200 bps or 38400 bps as the baud rate of COM Communication.

STEP 7 SIEMENS USB TO MPI SOFTWARE

Please note that Siemens COM port in programming software is up to support the option to COM8.But the ports more than COM8 are able to choose but in fact can not be used!Д®nter the main interface of STEP7 programming software (SIMATIC Manager), click on the 'Set PG / PC InterfaceвЂ¦' option under 'Options' menu into the PG / PC interface settings.ДЎ, Double-click on 'PC Adapter (MPI)' to set the parameters of COM port and MPI port. Quit the software and plug a USB plug or re-install the USB driver. If the COM port in the programming software with '*' symbols, such as '* COM3', itвЂ™s shown that the COM port have faults. Here are requested to indicate that 'USB' option in the local communications interface setting which the software is not support to the programming cable. And the following steps are exactly the same as in the traditional programming cables with RS232 interfaces. The step next is just to choose this COM port in the programming software and other application software and keep other communication parameters as in the Default settings. After completing Driver installation, the corresponding COM port for the USB/MPI+ programming cable will be displayed in the вЂњDevice ManagerвЂќ of Window.

STEP 7 SIEMENS USB TO MPI DRIVERS

USB device drivers should be installed before using USB/MPI+ programming cable.

One pc supports one USB programming cable only.

Support long distance communication up toВ 1000m.

Baud rate of MPI port on PLC: 19.2Kbps~187.5Kbps.

Baud rate of Com port on PC: 19.2Kbps~115.2Kbps.

The RS485 port design with overcurrent protection and lightning protection(500W)

The USB port design with surge protection.

High optoelectronic isolation voltage up to 1000VDC.

Power supply by both USB main line and MPI programming port(Total 1W).with Overcurrent Protection and Surge Protection.

Fully compatible with USB V1.1 and USB V2.0.

Signals definition of the RS485-Block (DB9M) of the USB/MPI + pin

STEP 7 SIEMENS USB TO MPI SERIAL

USB/MPI+В programming cable simulate USB port as traditional serial port (usually COM3), which enables existing programming software(STEP 7) to communicate through simulated traditional port and PLC devices. In particular, it applies to the strong interfere industrial scene and the safeguard in the circuit guarantees the safely running of the system. ItвЂ™s suitable for the communication between Siemens S7-300/400 series PLC or other equipments with MPI interface and computer. There is anti-surging& anti-lightning protection circuit for the USB and RS485 interface. USB/MPI+ is the optoelectronic isolated adapter for industrial design. Optoelectronic isolated USB/MPI V2.0,Siemens S7-300/400 PLC Programming adapter cable,3 meters,with communication indicator,can replace Siemens 6ES7 972-0CB20-0XA0,automatically adjust the communication speed from 19.2Kbps to 115.2Kbps for the PC port,automatically adjust the communication speed from 19.2Kbps to 187.5Kbps for the MPI interface.It doesn't support profibus function. This is USB/MPI+ V2.0 only for Siemens S7-300/400 PLC.Now USB/MPI+ V4.0 is available.USB/MPI+ V4.0 is for SiemensВ S7-200/300/400 PLC programming adapter,use Siemens original driver. USB/MPI+ V2.0:USB isolated Siemens S7-300/400 PLC adapter

Step 7 siemens usb to mpi